lakostis kernels discuss list

[Konstantin Lepikhov <>]

Hi Шенцев!

On 09/09/13, at 12:52:31 AM you wrote:

> 09.09.2013 00:33, Konstantin Lepikhov пишет:
> > А теперь еще раз вывод lspci -nnvv 
> 
> Во вложении.
> 
> > (выполнять от рута) 
> 
> Ой, Костя, такие вещи разжовываешь участнику ALT Team ... ;)
> 
тут дело не в тим, а что если не от рута, часть параметров lspci не
покажет.

> > Похоже никто вашей карты не видит, потому что ее pciid неизвестен. Вот
> > почему он незвестен будем разбираться. 
> 
> А по чему её видит fglrx?
> 
У меня есть подозрение, что модуль radeon у вас заблокирован. Покажите
вывод команды

# fgrep -ri radeon /etc/modprobe.d

Если есть что-то про blacklist (или вообще ничего нет), то уберите эти
строки, и добавьте следущее:

# fgrep -ir radeon /etc/modprobe.d/
/etc/modprobe.d/radeon-kms.conf:options radeon modeset=1

затем depmod -a && make-initrd && reboot

> 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor 
> Family DRAM Controller [8086:0100] (rev 09)
>       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort+ >SERR- <PERR- INTx-
>       Latency: 0
>       Capabilities: [e0] Vendor Specific Information: Len=0c <?>
> 
> 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation 
> Core Processor Family PCI Express Root Port [8086:0101] (rev 09) (prog-if 
> 00 [Normal decode])
>       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx+
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0, Cache Line Size: 4 bytes
>       Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>       I/O behind bridge: 0000d000-0000dfff
>       Memory behind bridge: fbe00000-fbefffff
>       Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
>       Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- <SERR- <PERR-
>       BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
>               PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>       Capabilities: [88] Subsystem: Gigabyte Technology Co., Ltd Device 
> [1458:5000]
>       Capabilities: [80] Power Management version 3
>               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>               Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
>       Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
>               Address: fee0f00c  Data: 4181
>       Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
>               DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, 
> L1 <1us
>                       ExtTag- RBE+ FLReset-
>               DevCtl: Report errors: Correctable- Non-Fatal- Fatal- 
> Unsupported-
>                       RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
>                       MaxPayload 128 bytes, MaxReadReq 128 bytes
>               DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- 
> TransPend-
>               LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM L0s L1, Latency 
> L0 <256ns, L1 <4us
>                       ClockPM- Surprise- LLActRep- BwNot+
>               LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- 
> CommClk+
>                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>               LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ 
> DLActive- BWMgmt+ ABWMgmt-
>               SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- 
> Surprise-
>                       Slot #1, PowerLimit 0.000W; Interlock- NoCompl+
>               SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- 
> HPIrq- LinkChg-
>                       Control: AttnInd Unknown, PwrInd Unknown, Power- 
> Interlock-
>               SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ 
> Interlock-
>                       Changed: MRL- PresDet+ LinkState-
>               RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- 
> CRSVisible-
>               RootCap: CRSVisible-
>               RootSta: PME ReqID 0000, PMEStatus- PMEPending-
>               DevCap2: Completion Timeout: Not Supported, TimeoutDis-, 
> LTR+, OBFF Not Supported ARIFwd-
>               DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, 
> OBFF Disabled ARIFwd-
>               LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
>                        Transmit Margin: Normal Operating Range, 
> EnterModifiedCompliance- ComplianceSOS-
>                        Compliance De-emphasis: -6dB
>               LnkSta2: Current De-emphasis Level: -6dB, 
> EqualizationComplete-, EqualizationPhase1-
>                        EqualizationPhase2-, EqualizationPhase3-, 
> LinkEqualizationRequest-
>       Capabilities: [100 v1] Virtual Channel
>               Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
>               Arb:    Fixed- WRR32- WRR64- WRR128-
>               Ctrl:   ArbSelect=Fixed
>               Status: InProgress-
>               VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
>                       Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
>                       Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
>                       Status: NegoPending- InProgress-
>       Capabilities: [140 v1] Root Complex Link
>               Desc:   PortNumber=02 ComponentID=01 EltType=Config
>               Link0:  Desc:   TargetPort=00 TargetComponent=01 AssocRCRB- 
> LinkType=MemMapped LinkValid+
>                       Addr:   0000000000009000
>       Kernel driver in use: pcieport
> 
> 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 
> Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
>       Subsystem: Gigabyte Technology Co., Ltd Device [1458:1c3a]
>       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx+
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0
>       Interrupt: pin A routed to IRQ 41
>       Region 0: Memory at fbfff000 (64-bit, non-prefetchable) [size=16]
>       Capabilities: [50] Power Management version 3
>               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>               Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
>       Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
>               Address: 00000000fee0f00c  Data: 4191
>       Kernel driver in use: mei_me
> 
> 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series 
> Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) 
> (prog-if 20 [EHCI])
>       Subsystem: Gigabyte Technology Co., Ltd Device [1458:5006]
>       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0
>       Interrupt: pin C routed to IRQ 18
>       Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=1K]
>       Capabilities: [50] Power Management version 2
>               Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA 
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>               Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>       Capabilities: [58] Debug port: BAR=1 offset=00a0
>       Capabilities: [98] PCI Advanced Features
>               AFCap: TP+ FLR+
>               AFCtrl: FLR-
>               AFStatus: TP-
>       Kernel driver in use: ehci-pci
> 
> 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset 
> Family High Definition Audio Controller [8086:1c20] (rev 05)
>       Subsystem: Gigabyte Technology Co., Ltd Device [1458:a002]
>       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx+
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0, Cache Line Size: 4 bytes
>       Interrupt: pin A routed to IRQ 42
>       Region 0: Memory at fbff8000 (64-bit, non-prefetchable) [size=16K]
>       Capabilities: [50] Power Management version 2
>               Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA 
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>               Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>       Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
>               Address: 00000000fee0f00c  Data: 41c1
>       Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 
> 00
>               DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, 
> L1 <1us
>                       ExtTag- RBE- FLReset+
>               DevCtl: Report errors: Correctable- Non-Fatal- Fatal- 
> Unsupported-
>                       RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
>                       MaxPayload 128 bytes, MaxReadReq 128 bytes
>               DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ 
> TransPend-
>               LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, 
> Latency L0 <64ns, L1 <1us
>                       ClockPM- Surprise- LLActRep- BwNot-
>               LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
>                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>               LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- 
> DLActive- BWMgmt- ABWMgmt-
>       Capabilities: [100 v1] Virtual Channel
>               Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
>               Arb:    Fixed- WRR32- WRR64- WRR128-
>               Ctrl:   ArbSelect=Fixed
>               Status: InProgress-
>               VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
>                       Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
>                       Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
>                       Status: NegoPending- InProgress-
>               VC1:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
>                       Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
>                       Ctrl:   Enable+ ID=1 ArbSelect=Fixed TC/VC=02
>                       Status: NegoPending- InProgress-
>       Capabilities: [130 v1] Root Complex Link
>               Desc:   PortNumber=0f ComponentID=00 EltType=Config
>               Link0:  Desc:   TargetPort=00 TargetComponent=00 AssocRCRB- 
> LinkType=MemMapped LinkValid+
>                       Addr:   00000000fed1c000
>       Kernel driver in use: snd_hda_intel
> 
> 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset 
> Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal 
> decode])
>       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0, Cache Line Size: 4 bytes
>       Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
>       I/O behind bridge: 00002000-00002fff
>       Memory behind bridge: f0000000-f01fffff
>       Prefetchable memory behind bridge: 00000000f0200000-00000000f03fffff
>       Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- <SERR- <PERR-
>       BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
>               PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>       Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
>               DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, 
> L1 <1us
>                       ExtTag- RBE+ FLReset-
>               DevCtl: Report errors: Correctable- Non-Fatal- Fatal- 
> Unsupported-
>                       RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
>                       MaxPayload 128 bytes, MaxReadReq 128 bytes
>               DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ 
> TransPend-
>               LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s, Latency L0 
> <1us, L1 <64us
>                       ClockPM- Surprise- LLActRep+ BwNot-
>               LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- 
> CommClk-
>                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>               LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ 
> DLActive- BWMgmt- ABWMgmt-
>               SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ 
> Surprise+
>                       Slot #16, PowerLimit 10.000W; Interlock- NoCompl+
>               SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- 
> HPIrq- LinkChg-
>                       Control: AttnInd Unknown, PwrInd Unknown, Power- 
> Interlock-
>               SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- 
> Interlock-
>                       Changed: MRL- PresDet- LinkState-
>               RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- 
> CRSVisible-
>               RootCap: CRSVisible-
>               RootSta: PME ReqID 0000, PMEStatus- PMEPending-
>               DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, 
> OBFF Not Supported ARIFwd-
>               DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis-, 
> LTR-, OBFF Disabled ARIFwd-
>               LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- 
> SpeedDis-
>                        Transmit Margin: Normal Operating Range, 
> EnterModifiedCompliance- ComplianceSOS-
>                        Compliance De-emphasis: -6dB
>               LnkSta2: Current De-emphasis Level: -3.5dB, 
> EqualizationComplete-, EqualizationPhase1-
>                        EqualizationPhase2-, EqualizationPhase3-, 
> LinkEqualizationRequest-
>       Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
>               Address: 00000000  Data: 0000
>       Capabilities: [90] Subsystem: Gigabyte Technology Co., Ltd Device 
> [1458:5001]
>       Capabilities: [a0] Power Management version 2
>               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>               Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>       Kernel driver in use: pcieport
> 
> 00:1c.1 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset 
> Family PCI Express Root Port 2 [8086:1c12] (rev b5) (prog-if 00 [Normal 
> decode])
>       Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0, Cache Line Size: 4 bytes
>       Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
>       Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort+ <SERR- <PERR-
>       BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
>               PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>       Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
>               DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, 
> L1 <1us
>                       ExtTag- RBE+ FLReset-
>               DevCtl: Report errors: Correctable- Non-Fatal- Fatal- 
> Unsupported-
>                       RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
>                       MaxPayload 128 bytes, MaxReadReq 128 bytes
>               DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ 
> TransPend-
>               LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency 
> L0 <1us, L1 <4us
>                       ClockPM- Surprise- LLActRep+ BwNot-
>               LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- 
> CommClk-
>                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>               LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
> DLActive+ BWMgmt+ ABWMgmt-
>               SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- 
> Surprise-
>                       Slot #1, PowerLimit 10.000W; Interlock- NoCompl+
>               SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- 
> HPIrq- LinkChg-
>                       Control: AttnInd Unknown, PwrInd Unknown, Power- 
> Interlock-
>               SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ 
> Interlock-
>                       Changed: MRL- PresDet- LinkState+
>               RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- 
> CRSVisible-
>               RootCap: CRSVisible-
>               RootSta: PME ReqID 0000, PMEStatus- PMEPending-
>               DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, 
> OBFF Not Supported ARIFwd-
>               DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis-, 
> LTR-, OBFF Disabled ARIFwd-
>               LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
>                        Transmit Margin: Normal Operating Range, 
> EnterModifiedCompliance- ComplianceSOS-
>                        Compliance De-emphasis: -6dB
>               LnkSta2: Current De-emphasis Level: -3.5dB, 
> EqualizationComplete-, EqualizationPhase1-
>                        EqualizationPhase2-, EqualizationPhase3-, 
> LinkEqualizationRequest-
>       Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
>               Address: 00000000  Data: 0000
>       Capabilities: [90] Subsystem: Gigabyte Technology Co., Ltd Device 
> [1458:5001]
>       Capabilities: [a0] Power Management version 2
>               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>               Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>       Kernel driver in use: pcieport
> 
> 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset 
> Family PCI Express Root Port 5 [8086:1c18] (rev b5) (prog-if 00 [Normal 
> decode])
>       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0, Cache Line Size: 4 bytes
>       Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
>       I/O behind bridge: 0000e000-0000efff
>       Memory behind bridge: fbd00000-fbdfffff
>       Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- <SERR- <PERR-
>       BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
>               PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>       Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
>               DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, 
> L1 <1us
>                       ExtTag- RBE+ FLReset-
>               DevCtl: Report errors: Correctable- Non-Fatal- Fatal- 
> Unsupported-
>                       RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
>                       MaxPayload 128 bytes, MaxReadReq 128 bytes
>               DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ 
> TransPend-
>               LnkCap: Port #5, Speed 5GT/s, Width x1, ASPM L0s L1, Latency 
> L0 <512ns, L1 <4us
>                       ClockPM- Surprise- LLActRep+ BwNot-
>               LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- 
> CommClk+
>                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>               LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
> DLActive+ BWMgmt+ ABWMgmt-
>               SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- 
> Surprise-
>                       Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
>               SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- 
> HPIrq- LinkChg-
>                       Control: AttnInd Unknown, PwrInd Unknown, Power- 
> Interlock-
>               SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ 
> Interlock-
>                       Changed: MRL- PresDet- LinkState+
>               RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- 
> CRSVisible-
>               RootCap: CRSVisible-
>               RootSta: PME ReqID 0000, PMEStatus- PMEPending-
>               DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, 
> OBFF Not Supported ARIFwd-
>               DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis-, 
> LTR-, OBFF Disabled ARIFwd-
>               LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
>                        Transmit Margin: Normal Operating Range, 
> EnterModifiedCompliance- ComplianceSOS-
>                        Compliance De-emphasis: -6dB
>               LnkSta2: Current De-emphasis Level: -3.5dB, 
> EqualizationComplete-, EqualizationPhase1-
>                        EqualizationPhase2-, EqualizationPhase3-, 
> LinkEqualizationRequest-
>       Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
>               Address: 00000000  Data: 0000
>       Capabilities: [90] Subsystem: Gigabyte Technology Co., Ltd Device 
> [1458:5001]
>       Capabilities: [a0] Power Management version 2
>               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>               Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>       Kernel driver in use: pcieport
> 
> 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series 
> Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) 
> (prog-if 20 [EHCI])
>       Subsystem: Gigabyte Technology Co., Ltd Device [1458:5006]
>       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0
>       Interrupt: pin A routed to IRQ 23
>       Region 0: Memory at fbffd000 (32-bit, non-prefetchable) [size=1K]
>       Capabilities: [50] Power Management version 2
>               Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA 
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>               Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>       Capabilities: [58] Debug port: BAR=1 offset=00a0
>       Capabilities: [98] PCI Advanced Features
>               AFCap: TP+ FLR+
>               AFCtrl: FLR-
>               AFStatus: TP-
>       Kernel driver in use: ehci-pci
> 
> 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] 
> (rev a5) (prog-if 01 [Subtractive decode])
>       Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0
>       Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
>       Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- <MAbort+ <SERR- <PERR-
>       BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
>               PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>       Capabilities: [50] Subsystem: Gigabyte Technology Co., Ltd 
> Motherboard [1458:5000]
> 
> 00:1f.0 ISA bridge [0601]: Intel Corporation H61 Express Chipset Family LPC 
> Controller [8086:1c5c] (rev 05)
>       Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001]
>       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR+ FastB2B- DisINTx-
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0
>       Capabilities: [e0] Vendor Specific Information: Len=0c <?>
>       Kernel driver in use: lpc_ich
> 
> 00:1f.2 IDE interface [0101]: Intel Corporation 6 Series/C200 Series 
> Chipset Family 4 port SATA IDE Controller [8086:1c00] (rev 05) (prog-if 8f 
> [Master SecP SecO PriP PriO])
>       Subsystem: Gigabyte Technology Co., Ltd Device [1458:b002]
>       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0
>       Interrupt: pin B routed to IRQ 19
>       Region 0: I/O ports at ff00 [size=8]
>       Region 1: I/O ports at fe00 [size=4]
>       Region 2: I/O ports at fd00 [size=8]
>       Region 3: I/O ports at fc00 [size=4]
>       Region 4: I/O ports at fb00 [size=16]
>       Region 5: I/O ports at fa00 [size=16]
>       Capabilities: [70] Power Management version 3
>               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>               Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
>       Capabilities: [b0] PCI Advanced Features
>               AFCap: TP+ FLR+
>               AFCtrl: FLR-
>               AFStatus: TP-
>       Kernel driver in use: ata_piix
> 
> 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family 
> SMBus Controller [8086:1c22] (rev 05)
>       Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001]
>       Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Interrupt: pin C routed to IRQ 18
>       Region 0: Memory at fbffc000 (64-bit, non-prefetchable) [size=256]
>       Region 4: I/O ports at 0500 [size=32]
>       Kernel driver in use: i801_smbus
> 
> 00:1f.5 IDE interface [0101]: Intel Corporation 6 Series/C200 Series 
> Chipset Family 2 port SATA IDE Controller [8086:1c08] (rev 05) (prog-if 85 
> [Master SecO PriO])
>       Subsystem: Gigabyte Technology Co., Ltd Device [1458:b002]
>       Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0
>       Interrupt: pin B routed to IRQ 19
>       Region 0: I/O ports at f800 [size=8]
>       Region 1: I/O ports at f700 [size=4]
>       Region 2: I/O ports at f600 [size=8]
>       Region 3: I/O ports at f500 [size=4]
>       Region 4: I/O ports at f400 [size=16]
>       Region 5: I/O ports at f300 [size=16]
>       Capabilities: [70] Power Management version 3
>               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>               Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
>       Capabilities: [b0] PCI Advanced Features
>               AFCap: TP+ FLR+
>               AFCtrl: FLR-
>               AFStatus: TP-
>       Kernel driver in use: ata_piix
> 
> 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. 
> [AMD/ATI] Juniper PRO [Radeon HD 6750] [1002:68bf] (prog-if 00 [VGA 
> controller])
>       Subsystem: Hightech Information System Ltd. Device [1787:2014]
>       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0, Cache Line Size: 4 bytes
>       Interrupt: pin A routed to IRQ 10
>       Region 0: Memory at e0000000 (64-bit, prefetchable) [size=256M]
>       Region 2: Memory at fbec0000 (64-bit, non-prefetchable) [size=128K]
>       Region 4: I/O ports at de00 [size=256]
>       [virtual] Expansion ROM at fbe00000 [disabled] [size=128K]
>       Capabilities: [50] Power Management version 3
>               Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>               Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>       Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
>               DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, 
> L1 unlimited
>                       ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
>               DevCtl: Report errors: Correctable- Non-Fatal- Fatal- 
> Unsupported-
>                       RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
>                       MaxPayload 128 bytes, MaxReadReq 512 bytes
>               DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- 
> TransPend-
>               LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, 
> Latency L0 <64ns, L1 <1us
>                       ClockPM- Surprise- LLActRep- BwNot-
>               LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- 
> CommClk+
>                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>               LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ 
> DLActive- BWMgmt- ABWMgmt-
>               DevCap2: Completion Timeout: Not Supported, TimeoutDis-, 
> LTR-, OBFF Not Supported
>               DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, 
> OBFF Disabled
>               LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- 
> SpeedDis-
>                        Transmit Margin: Normal Operating Range, 
> EnterModifiedCompliance- ComplianceSOS-
>                        Compliance De-emphasis: -6dB
>               LnkSta2: Current De-emphasis Level: -6dB, 
> EqualizationComplete-, EqualizationPhase1-
>                        EqualizationPhase2-, EqualizationPhase3-, 
> LinkEqualizationRequest-
>       Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
>               Address: 0000000000000000  Data: 0000
>       Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 
> Len=010 <?>
>       Capabilities: [150 v1] Advanced Error Reporting
>               UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
>               UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
>               UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- 
> RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
>               CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- 
> NonFatalErr+
>               CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- 
> NonFatalErr+
>               AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ 
> ChkEn-
> 
> 01:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] Juniper 
> HDMI Audio [Radeon HD 5700 Series] [1002:aa58]
>       Subsystem: Hightech Information System Ltd. Device [1787:aa58]
>       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx+
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0, Cache Line Size: 4 bytes
>       Interrupt: pin B routed to IRQ 43
>       Region 0: Memory at fbefc000 (64-bit, non-prefetchable) [size=16K]
>       Capabilities: [50] Power Management version 3
>               Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>               Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>       Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
>               DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, 
> L1 unlimited
>                       ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
>               DevCtl: Report errors: Correctable- Non-Fatal- Fatal- 
> Unsupported-
>                       RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
>                       MaxPayload 128 bytes, MaxReadReq 512 bytes
>               DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- 
> TransPend-
>               LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, 
> Latency L0 <64ns, L1 <1us
>                       ClockPM- Surprise- LLActRep- BwNot-
>               LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- 
> CommClk+
>                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>               LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ 
> DLActive- BWMgmt- ABWMgmt-
>               DevCap2: Completion Timeout: Not Supported, TimeoutDis-, 
> LTR-, OBFF Not Supported
>               DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, 
> OBFF Disabled
>               LnkSta2: Current De-emphasis Level: -6dB, 
> EqualizationComplete-, EqualizationPhase1-
>                        EqualizationPhase2-, EqualizationPhase3-, 
> LinkEqualizationRequest-
>       Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
>               Address: 00000000fee0f00c  Data: 41d1
>       Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 
> Len=010 <?>
>       Capabilities: [150 v1] Advanced Error Reporting
>               UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
>               UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
>               UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- 
> RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
>               CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- 
> NonFatalErr+
>               CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- 
> NonFatalErr+
>               AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ 
> ChkEn-
>       Kernel driver in use: snd_hda_intel
> 
> 03:00.0 PCI bridge [0604]: Integrated Technology Express, Inc. Device 
> [1283:8892] (rev 30) (prog-if 00 [Normal decode])
>       Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0, Cache Line Size: 4 bytes
>       Bus: primary=03, secondary=04, subordinate=04, sec-latency=32
>       Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- 
> <TAbort- <MAbort+ <SERR- <PERR-
>       BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
>               PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
>       Capabilities: [70] #00 [0000]
> 
> 05:00.0 Ethernet controller [0200]: Qualcomm Atheros AR8151 v2.0 Gigabit 
> Ethernet [1969:1083] (rev c0)
>       Subsystem: Gigabyte Technology Co., Ltd Device [1458:e000]
>       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>       Latency: 0, Cache Line Size: 4 bytes
>       Interrupt: pin A routed to IRQ 44
>       Region 0: Memory at fbdc0000 (64-bit, non-prefetchable) [size=256K]
>       Region 2: I/O ports at ef00 [size=128]
>       Capabilities: [40] Power Management version 3
>               Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA 
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
>               Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
>       Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+
>               Address: 00000000fee0f00c  Data: 41e1
>       Capabilities: [58] Express (v1) Endpoint, MSI 00
>               DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s 
> unlimited, L1 unlimited
>                       ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset-
>               DevCtl: Report errors: Correctable- Non-Fatal- Fatal- 
> Unsupported-
>                       RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
>                       MaxPayload 128 bytes, MaxReadReq 512 bytes
>               DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ 
> TransPend-
>               LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s Lpcilib: 
> sysfs_read_vpd: read failed: Connection timed out
> 1, Latency L0 unlimited, L1 unlimited
>                       ClockPM+ Surprise- LLActRep- BwNot-
>               LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- 
> CommClk+
>                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>               LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
> DLActive- BWMgmt- ABWMgmt-
>       Capabilities: [6c] Vital Product Data
>               Not readable
>       Capabilities: [100 v1] Advanced Error Reporting
>               UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
> RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
>               UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
>               UESvrt: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
> RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
>               CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- 
> NonFatalErr-
>               CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- 
> NonFatalErr+
>               AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ 
> ChkEn-
>       Capabilities: [180 v1] Device Serial Number ff-a5-02-f2-50-e5-49-ff
>       Kernel driver in use: atl1c
> 

> _______________________________________________
> Kernels mailing list
> 
> https://lists.unsafe.ru/mailman/listinfo/kernels


-- 
WBR et al.